530 process pumps for use with continuous tubing

Pumpheads for up to 3.5 L/min

Pumpheads for up to 3.5 L/min

Contact us


To order this product please contact UK Sales Support:

Phone: +44 (0) 1326 370362

You can also send us an email or find your nearest distributor.

Overview

530S and SN, 530U and UN, 530Du and DuN 530Bp and BpN, 530En and EnN fitted with 520R and 520R2 continuous tubing pumpheads

530 range of process pumps offer four drive options, colour display and intuitive menu structures provide visual status indication and minimal key presses.

Control

Pump drives 530S 530SN 530U 530UN 530Du 530DuN 530Bp 530BpN 530US 530DuS 530En 530EnN
Manual control                        
Intuitive keypad and color display
Choice of flowrate or speed display
Full calibration with choice of flow units
MemoDose function        
Auto restart facility
Leak detection
Remote control                        
Configurable Start/Stop, leak detector and pressure switch input via contact closure or 5V TTL or 24V industrial logic        
Configurable Start/Stop, leak detector and pressure switch input via 110V industrial logic        
Configurable Start/Stop and leak detector input via contact closure or 5V TTL or 24V industrial logic Note: Does not include pressure switch        
Direction change and auto/manual toggle input via contact closure or 5V TTL or 24V industrial logic        
Direction change and auto/manual toggle input via 110V industrial logic        
Remote operation of MemDose (foot/hand-switch or logic input)        
Four configurable digital status outputs through 24V, 30W relays            
Four configurable digital status outputs through 110V relays            
Software configurable logic outputs                    
Remote pressure/flow sensors                    
Analogue speed control                        
Fully configurable inputs; 0-10V or 4-20mA        
Analogue outputs; 0-10V, 4-20Ma            
Keypad/analogue input scaling (replacement of diaphragm pumps)                  
Tacho frequency output; 0-991Hz                
2x sensor inputs 4-20ma*                    
Security                        
3-level PIN lock
Network communication                        
RS485 network control                    
RS232 network control                      
Digital pump commands (Profibus / EtherNet/IP)                        
Profibus DP V0                    
Communication speeds from 9.6kbit/s up to 12000kbit/s                    
Auto detect bus speed                
Speed set point                
Speed feedback                
Flow calibration function                
Hours run                
Revolution counter                
Leak detection                
Low fluid level alarm                
Diagnostic feedback                
EtherNet/IP                
Device Level Ring (DLR)                    
Flow Totaliser                
Baud Rate (MBPS) 10/100 Full/Half Duplex Operation                

Performance

Tube bore and flow rates (ml/min)
Tube material Speed 0.5mm 1.6mm 3.2mm 4.8mm 6.4mm 8.0mm  9.6mm
STA-PURE PCS, STA-PURE PFL, Pumpsil, Neoprene 0.1 to 220rpm 0.004-9.5 0.04-97 0.18-390 0.40-870 0.70-1500 1.1-2400 1.6 - 3500
Marprene/Bioprene, Pureweld XL 0.1 to 220rpm 0.004-9.0 0.04-92 0.17-370 0.38-830 0.67-1500 1.1-2300 1.5 - 3300

Drives

Simple-to use HMI requiring minimal key presses to reduce chances of costly errors. Flow proportional to pump speed over 2,200:1 control range. IP31 and IP66 cased pumps for washdown environments.

Tubing

Please refer to datasheets for materials and sizes of continuous tubing and tube elements for each pumphead model.

Pumpsil platinum cured silicone tubing

Pumpsil platinum-cured silicone tubing

Bioprene thermoplastic tubing Bioprene industrial grade tubing

 

PureWeld

Watson-Marlow tubing - PureWeld

 
Marprene long life process tubing Marprene industrial grade thermoplastic elastomer tubing

 

GORE STA-PURE PCS reinforced silicone tubing GORE STA-PURE PCS pump tubing

 

GORE STA-PURE PFL reinforced fluoroelastomer tubing GORE STA-PURE PFL pump tubing

 

Neoprene industrial application tubing Neoprene tubing elements

 





Take a tour

Datasheets

530 datasheet (UK)

Tubing and hoses for your industry

  • Contact us

    To order this product please contact UK Sales Support:

    Phone: +44 (0) 1326 370362

    You can also send us an email or find your nearest distributor.