630 Process pumps for use with continuous tubing

To order this product please contact us on:

Telephone: +64 (0)9 273 3166

Fax: +64 (0)9 273 3167

You can also send us an email

630S and SN, 630U and UN, 630Du and DuN, 630Bp and BpN peristaltic process pumps fitted with 620R continuous tubing pumpheads

630 range of peristaltic process pumps offer four drive options, colour display and intuitive menu structures provide visual status indication and minimal key presses
Flow rates up to 16 litre/min at 2 bar peak pressure
Industrial integration - manual, remote, Analog and digital communication, plus PROFIBUS
Keypad incorporates 3-level security PIN lock
Retractable rollers for easy tube loading and a rugged tool-lockable guard
620R pumphead for use with Watson-Marlow continuous tubing
S, U, Du and Bp pumps are IP31 rated cased pump. SN, UN, DuN and BpN are IP66 rated cased pumps

Pump drives	630SN	630UN	630DuN	630BpN	630S	630U	630Du	630Bp
Manual control
Intuitive keypad and colour display	•	•	•	•	•	•	•	•
Choice of flowrate or speed display	•	•	•	•	•	•	•	•
Full calibration with choice of flow units	•	•	•		•	•	•	•
Remote control
Configurable Start/Stop, leak detector and pressure switch input (via contact closure or 5V TTL or 24V industrial logic)		•	•			•	•
Direction change and auto/manual toggle input (via contact closure or 5V TTL or 24V industrial logic)		•	•			•	•
Remote operation of MemDose (foot/hand-switch or logic input)		•	•			•	•
Four configurable digital status outputs through 24V, 30W relays		•	•
Software configurable IP31 outputs						•	•
Analogue speed control
Fully configurable inputs; 0-10V or 4-20mA		•	•			•	•
Analogue outputs; 0-10V, 4-20Ma		•	•			•	•
Keypad / analogue input scaling (replacement of diaphragm pumps)			•				•
Tacho frequency output; 0-1478Hz		•	•			•	•
Digital communication
RS485 network control			•
RS232 network control							•
Fieldbus technology
Profibus DP V0
Communication speeds from 9.6kbit/s up to 12000kbit/s				•				•
Auto detect bus speed				•				•
Security				•				•
3-level PIN lock	•	•	•	•	•	•	•	•

Flow ranges (l/min)	Continuous tubing				LoadSure TM element tubing
	620R (2 rollers)				620RE (2 rollers)		620RE4 (2 rollers)
Tubing material, tubing bore (mm)	6.4mm	9.6mm	12.7mm	15.9mm	12mm	17mm	12mm	17mm
Marprene TM, Bioprene TM					0.004-9.8	0.01-16	0.003-8.3	0.004-11
Marprene TL, Bioprene TL	0.001-3.4	0.003-6.6	0.004-11	0.01-12	0.004-9.8	0.01-18	0.003-8.3	0.005-12
Pumpsil® silicone	0.001-3.2	0.003-7.2	0.004-11	0.01-15	0.004-10	0.01-16	0.003-8.7	0.004-11
Sta-PURE™, Chem-Sure™, Neoprene	0.001-3.2	0.003-6.6	0.004-11	0.01-16	0.004-11	0.01-18	0.003-9.0	0.010-13

620R continuous tubing pumphead

620R pumphead accommodates 3.2mm wall continuous tubing in four bore sizes from 6.4mm to 15.9mm, giving up to 16 litre/min flow at up to 2 bar pressure.
Tubing is available in eight materials for almost any chemical requirement.

620RE LoadSure tube element pumphead

620RE is a high-performance, accurate, two-roller pumphead with LoadSure rapid tube element change technology.
4mm wall elements in 12mm or 17mm bore sizes allow pressures up to 4 bar and flow rates up to 18 litre/min.
Elements are available with industry-standard tri-clamp sanitary fittings; and with Cam and Groove fittings for industry.

620RE4 LoadSure tube element pumphead

620RE4 is a high-performance, accurate, four-roller pumphead with LoadSure rapid tube element change technology. 4mm wall elements in 12mm or 17mm bore sizes allow pressures up to 4 bar and flow rates up to 13 litre/min with minimized pulsation.
Elements are available with industry-standard tri-clamp sanitary fittings; and with Cam and Groove fittings for industry.

620L twin-channel pumphead

620L is a specialist 2 bar, six-roller pumphead designed for accurate dispensing to ±0.5%. Minimal pulsation is achieved by splitting the inlet flow into two tubes passing over twin, offset tracks. The two sets of out-of-phase pulses cancel each other out when the channels merge.
Uses 4.0mm wall Y-elements in a choice of six materials, or continuous tubing
Two single channels are also available
Tubing choices: 8mm, 12mm, and 16mm bore, offering flow rates from 0.002 to 12.4 litre/min
Dispenses 500ml in 3.5 seconds

Simple-to use HMI requiring minimal key presses to reduce chances of costly errors. Flow proportional to pump speed over 2,650:1 control range. IP31 and IP66 cased pumps for washdown environments.
630S - IP31 and 630SN - IP66 are simple, plug-in and switch on pumps offering economy of ownership. Ultimate process security with a 3 level PIN lock.
630U - IP31 and 630UN - IP66 with all the features of the S/SN models, plus configurable inputs and outputs.
630Du - IP31 and 630DuN - IP66 with configurable inputs and outputs, plus RS232 and IP31 RS484.
630Bp - IP31 and 630BpN - IP66 Real time communication makes your process secure and flexible. Bus speed 9.6 kbits/s up to 12000 kbits/s connectivity

Please refer to datasheets for materials and sizes of continuous tubing and tube elements for each pumphead model.

Pumpsil platinum cured silicone tubing		Laser-etched part number, lot number and use-by-date accuracy Certification USP Class VI, FDA regulations 21 CFR177.2600 for contact with food -20 °C to 80 °C
Bioprene thermoplastic tubing		Fully approved for food and pharmaceutical applications Low permeability 5 °C to 80 °C
PureWeld		Low internal spallation ADCF -20 °C to 80 °C
Marprene long life process tubing		Exceptional long life Wide chemical compatibility, especially resistant to oxidizing agents 5 °C to 80 °C, up to 7 bar
GORE STA-PURE PCS reinforced silicone tubing		Longest available peristaltic tube life Virtually no spallation -20 °C to 80 °C, to 7 bar
GORE STA-PURE PFL reinforced fluoroelastomer tubing		Extreme chemical resistance 50 times longer life than other fluoroelastomers -20 °C to 80 °C, to 4 bar
Neoprene industrial application tubing		Handles abrasive slurries Up to 2 bar 0 °C to 80 °C