Process pump for tube elements

Manual, analog, digital or fieldbus control

Flow rates to 8.8 USGPM/33 litre minute

One minute maintenance transfer pumps

Contact Us

To order this product please contact us on:

Tel: +1 978 658 6168 and Toll free +1 800 282-8823

You can also send us an email or find your nearest distributor

Overview
Control
Performance
Pumpheads
Drives
Brochures
Download datasheet
Manual download
PROFIBUS

Overview

730SN, 730UN, 730DuN, 730BpN and 730EnN pumps fitted with tube element pumpheads

730 range of peristaltic pumps offer four drive options, colour display and intuitive menu structure provide visual status indication and minimal key presses.
Flows up to 8.8 USGPM 30 psi / 33 litre/min (2 bar) using LoadSure tube elements
Industrial integration - manual, remote, Analog and digital communication, plus PROFIBUS
Keypad incorporates 3-level security PIN lock
NEMA 4X (IP66) rated cased pumps

Control

Pump drives	730SN	730UN	730DuN	730BpN	730US	730DuS	730EnN
Manual control
Intuitive keypad and color display	•	•	•	•	•	•
Choice of flowrate or speed display	•	•	•	•	•	•	•
Full calibration with choice of flow units	•	•	•	•	•	•	•
MemoDose function	•	•	•		•	•
Auto restart facility	•	•	•	•	•	•	•
Guard switch detection	•	•	•	•	•	•	•
Leak detection	•	•	•	•	•	•	•
Remote control
Configurable Start/Stop, leak detector and pressure switch input via contact closure or 5V TTL or 24V industrial logic		•	•
Configurable Start/Stop, leak detector and pressure switch input via 110V industrial logic					•	•
Configurable Start/Stop and leak detector input via contact closure or 5V TTL or 24V industrial logic Note: Does not include pressure switch							•
Direction change and auto/manual toggle input via contact closure or 5V TTL or 24V industrial logic		•	•
Direction change and auto/manual toggle input via 110V industrial logic					•	•
Remote operation of MemDose (foot/hand-switch or logic input)		•	•		•	•
Four configurable digital status outputs through 24V, 30W relays		•	•
Four configurable digital status outputs through 110V relays					•	•
Remote pressure/flow sensors							•
Analogue speed control
Fully configurable inputs; 0-10V or 4-20mA		•	•		•	•
Analogue outputs; 0-10V, 4-20Ma		•	•		•	•
Keypad/analogue input scaling (replacement of diaphragm pumps)			•			•
Tacho frequency output; 0-1478Hz		•	•
2x sensor inputs 4-20ma*							•
Security
3-level PIN lock	•	•	•	•	•	•	•
Network communication
RS485 network control			•			•
Digital pump commands (Profibus / EtherNet/IP)
Profibus DP V0				•
Communication speeds from 9.6kbit/s up to 12000kbit/s				•
Baud Rate (MBPS) 10/100 Full/Half Duplex Operation							•
Auto detect bus speed							•
Speed set point				•			•
Speed feedback				•			•
Flow calibration function				•			•
Hours run				•			•
Revolution counter				•			•
Leak detection				•			•
Low fluid level alarm				•			•
Diagnostic feedback				•			•
EtherNet/IP							•
Device Level Ring (DLR)							•
Flow Totaliser							•

Performance

		Tube bore and flow rates (GPM)
	Speed rpm	12.7mm	15.9mm	19.0mm	25.4mm
720R	0.1-360	0.001-3.5	0.001-4.	0.002-6.6	0.003-8.8

Pumpheads

720RE and 720REX LoadSure tubing element pumpheads

720RE pumpheads accommodate 4.8mm-wall LoadSure tubing elements in two conformations: with PVDF Tri-clamp-style connectors for sanitary applications; and with industrial Cam-and-Groove connectors. Both are offered in four bore sizes: 12.7mm, 15.9mm, 19.0mm and 25.4mm, giving up to 8.8 GPM (2,000 l/hr) flow at up to 30 psi (2 bar) pressure.
720REX extension pumpheads offer identical performance, but at a maximum pressure of 15 psi (1 bar).

Elements are available in Pumpsil platinum-cured silicone, Bioprene and STA-PURE PCS for sanitary applications; and in Marprene, Pumpsil and Neoprene for industrial use.

720R and 720RX continuous tubing pumpheads

720R pumpheads accommodate 4.8mm wall continuous tubing for joint-free flow from source to discharge. Available in five bore sizes: 9.6mm, 12.7mm, 15.9mm 19.0mm and 25.4mm, giving up to 8.8 GPM (2,000 l/hr) flow at up to 30 psi (2 bar) pressure.
720RX extension pumpheads offer identical performance, but at a maximum pressure of 15 psi (1 bar).

Tubing is available in five materials for almost any chemical requirement.

Drives

Simple-to use HMI requiring minmal key presses to reduce chances of costly errors.Flow proprtional to pump speed over 3,600:1 control range. NEMA 4X (IP66) cased pumps for washdown environments.
730SN simple, plug-in and switch on pumps offereing economy of ownership. Ulitmate process security with a 3 level PIN lock.
730UN - with all the features of the SN models, plus configurable inputs and outputs.
730DuN with configurable inputs and outputs, plus RS232 and RS484.
730BpN – NEMA 4X Real time communication makes your process secure and flexible. Bus speed 9.6 kbits/s up to 12000 kbits/s connectivity
730EnN – NEMA 4X EtherNet/IP connectivity for fast and easy access to pump data over Industrial Ethernet

Brochures

Process pump brochures

Download datasheet

Manual download

730 operating manuals

PROFIBUS

No point-to-point wiring and a simple 9-pin PROFIBUS D-connector provides:

Two way communication for control and status feedback
Pumps communicate at full PROFIBUS bus speed
No additional gateways or I/O converters required
Predictive maintenance

Profibus GSD control file